Page 243 - IS-Rayfast Catalogue - Issue 9, 2017
P. 243
Terminals and Splices
D-436 Series
MiniSeal ®
Heat Shrinkable, Crimp Splice
BUTT (in-line) Splice - Selection Guide 1
Internal Dimensions
Crimp Barrel
Part Number Colour
Size Range End 1 End 2 2
Sealing Max. No. Sealing Max. No.
Tin Plated Nickel Plated CMA mm 2
Insert mm Wires Insert mm Wires 3
D-436-36 D-436-82 Red 304-1510 0.15-0.75 2.16 Ø 2 2.16 Ø 2
D-436-37 D-436-83 Blue 1058-2680 0.39-1.34 2.79 Ø 2 2.79 Ø 2
4
D-436-38 D-436-84 Yellow 2375-6755 0.95-3.37 4.32 Ø 2 4.32 Ø 2
D-436-0110 D-436-85 Red 304-1510 0.15-0.75 2.36 Ø 6* 4.06 Ø 2
5
D-436-52 D-436-86 Blue 1058-2680 0.39-1.34 2.36 Ø 6* 4.06 Ø 2
D-436-53 D-436-87 Yellow 2375-6755 0.95-3.37 2.36 Ø 6* 4.06 Ø 2
D-436-0115 D-436-88 Red 304-1510 0.15-0.75 2.36 Ø 6* 2.36 Ø 6* 6
D-436-42 D-436-89 Blue 1058-2680 0.39-1.34 2.36 Ø 6* 2.36 Ø 6*
D-436-43 D-436-90 Yellow 2375-6755 0.95-3.37 2.36 Ø 6* 2.36 Ø 6* 7
* Denotes max 2 wires per hole of insert
8
STUB (parallel) Splice - Selection Guide
Crimp Barrel Internal Ø Dimensions 9
Part Number Colour
Size Range
End 1 End 2
MIL Spec Tin Plated Nickel Plated CMA mm 2 Sealing Max. No. Sealing Max. No. 10
Part Number mm Range Wire Range Colour Code Insert Wires Insert mm Wires
2
Equivalent
D-436-0128 D-436-0119 Red 304-1510 0.15-0.75 2.16 2 1.01 2
D-436-36 M81824/-1-1 0.15 - 0.75 26 - 20 AWG Red
D-436-58 D-436-75 Blue 1058-2680 0.39-1.34 4.56 2 2.28 2 11
D-436-37 M81824/-1-2 0.39 - 1.34 20 -16 AWG Blue
D-436-59 D-436-76 Yellow 2375-6755 0.95-3.37 4.56 2 2.28 2
D-436-38 M81824/-1-3 0.95 - 3.37 16 - 12 AWG Yellow
D-436-60 D-436-77 Blue 1058-2680 0.39-1.34 2.03 10* 6.35 2 12
D-436-61 D-436-78 Yellow 2375-6755 0.95-3.37 2.03 10* 6.35 2
* Denotes max 2 wires per hole of insert
13
Product Characteristics Product Performance
14
Insulation Radiation crosslinked, heat-shrinkable polyvinylidene fluoride
Operating temperature -55ºC to +150ºC
15
Dielectric strength 2500 V Max
Insulation resistance after immersion 5000 Mega-ohms
16
Voltage drop 6.9 mV @ 4.5A vs 8.1 mV for an equal length of wire
Physical properties Tensile strength exceeds strength of spliced wire
17
Notes:
• The correct crimp tool AD-1377, must be used for proper installation of these devices.
• Heat guns are recommended for the installation of these devices: HL2010E and CV198X with the correct 18
reflector added. See Application Equipment Section.
www.is-rayfast.com 241